Replacement door sash moulding for my Honda 600 Coupe.

[Chuck Dean]

Replacement door sash moulding for my Honda 600 Coupe.
Hello everyone,
I need to replace the door sash moulding on my Z. I notice that Honda 600 Car Parts has some "Door Glass Front Channel "for a N600 Sedan. Shouldn't this be the same material that was used on the Z? I believe the window channel is the same width on both cars, which would be the critical measurement, since it is not cut to length.
Has anyone tried this?
Thanks,
Chuck (mobile)
Pleez x cuze enny tie ping or spelin air ores.

[Steve]

One of these might be what you are looking for and they will send you samples free of charge:
http://www.steelerubber.com/channel-weatherstripping
Miles

[Bill]

This is the size of channel weather strip I have used successfully on the Honda 600 Coupe and Sedan , it is � in. X 15/32 in. X 3/16 in.
which is what is needed.� When installing at the right angle corner, cut the back side to the edge (not all the way through) then it will fit and complete the needed look.� (Also this is the way the Honda OEM weather strip is).� Order suggested adhesive to keep it in place while the window runs in the channel, and replace all of it, not just the upper part.�
http://www.crlaurence.com/crlapps/showl ... 0812&pom=0
Bill

[Chuck Dean]

Hi Bill,� Thanks for the information. Between your dimensions, and Miles' website information, I was able to buy this channel direct.� Here's the link for future reference:
http://www.steelerubber.com/unbeaded-ru ... 70-3575-58 You guys are the best!
Chuck� Pleez x cuze enny tie ping or spelin air ores.

On Fri, Feb 17, 2017 at 10:13 AM, 'Bill'
billmyong@...
[2cylinderhondas]
�
> �
> This is the size of channel weather strip
> I have used successfully on the Honda 600 Coupe and
> Sedan
> , it is � in. X 15/32 in. X 3/16 in.
> which is what is needed.� When installing at the right angle corner, cut the > back side to the edge (not all the way through) then it will fit and complete > the needed look.� (Also this is the way the Honda OEM weather strip is).� Order > suggested adhesive to keep it in place while the window runs in the channel, > and replace all of it, not just the upper part.�
> �
> http://www.crlaurence.com/ crlapps/showline/offerpage. aspx?ProductID=17142&GroupID= 20812&History=30587:19748: 19770:19748:19780:20757& ModelID=20812&pom=0
> �
> Bill
> �
> From:
> 2cylinderhondas@yahoogroups. com
> [mailto:
> 2cylinderhondas@ yahoogroups.com
> ]
> Sent:
> Thursday, February 16, 2017
> 11:47 PM
> To:
> 2cylhondagroup
> Subject:
> [2cylinderhondas] Re:
> Replacement door sash moulding for my Honda 600 Coupe.
> �
> �
> One of these might be what you are looking
> for and they will send you samples free of charge:
> �
> http://www.steelerubber.com/ channel-weatherstripping
> �
> Miles

[Chuck Dean]

Hi bill, Did you have to remove the door panel to install this rubber channel? It looks borderline whether I can get down in the door, possibly with a 3/16 drillrod?
I hate to remove anything if I don't have to... Old parts break easily. :( Chuck (mobile) Pleez x cuze enny tie ping or spelin air ores.

On Feb 17, 2017, at 11:26 AM, Chuck Dean wrote:
Hi Bill,
Thanks for the information. Between your dimensions, and Miles' website information, I was able to buy this channel direct.
Here's the link for future reference:
http://www.steelerubber.com/unbeaded-ru ... 70-3575-58 You guys are the best!
Chuck
Pleez x cuze enny tie ping or spelin air ores.
On Fri, Feb 17, 2017 at 10:13 AM, 'Bill'
billmyong@...
[2cylinderhondas]
This is the size of channel weather strip
> I have used successfully on the Honda 600 Coupe and
> Sedan
> , it is � in. X 15/32 in. X 3/16 in.
> which is what is needed.  When installing at the right angle corner, cut the > back side to the edge (not all the way through) then it will fit and complete > the needed look.  (Also this is the way the Honda OEM weather strip is).  Order > suggested adhesive to keep it in place while the window runs in the channel, > and replace all of it, not just the upper part.
> http://www.crlaurence.com/ crlapps/showline/offerpage. aspx?ProductID=17142&GroupID= 20812&History=30587:19748: 19770:19748:19780:20757& ModelID=20812&pom=0
> Bill
> From:
> 2cylinderhondas@yahoogroups. com
> [mailto:
> 2cylinderhondas@ yahoogroups.com
> ]
> Sent:
> Thursday, February 16, 2017
> 11:47 PM
> To:
> 2cylhondagroup
> Subject:
> [2cylinderhondas] Re:
> Replacement door sash moulding for my Honda 600 Coupe.
> One of these might be what you are looking
> for and they will send you samples free of charge:
> http://www.steelerubber.com/ channel-weatherstripping
> Miles

Note: 1 image(s) originally linked in this post are no longer available (cid:).