Tail light gasket

[Chuck Dean]

Hello, I need a set of the gaskets between the tail light assembly and the body on my 1972 Honda 600 Coupe.
Is there any place to purchase NOS or reproductions?
Thanks, Chuck  (mobile) Pleez x cuze enny tie ping or spelin air ores.
Our 1972 Honda 600 Coupe Our 1961 Vespa 400

[J Graf]

When I put my tail light assemblies back on next week, I'm planning on copying the original gasket shape and cutting it out of a left over inner tube.

> On May 31, 2019, at 1:39 PM, Chuck Dean
> cadean329@...
> [2cylinderhondas] 2cylinderhondas@yahoogroups.com
> > wrote:
> Hello,
> I need a set of the gaskets between the tail light assembly and the body on my 1972 Honda 600 Coupe.
> Is there any place to purchase NOS or reproductions?

[art Remai]

I did that to sandwich the window in the medal rails of the driver and passenger window. Bicycle inner tube worked well.
Sent from my iPhone

On May 31, 2019, at 6:46 PM, J Graf
jgraf@...
[2cylinderhondas] wrote:
When I put my tail light assemblies back on next week, I'm planning on copying the original gasket shape and cutting it out of a left over inner tube.
> On May 31, 2019, at 1:39 PM, Chuck Dean
> cadean329@...
> [2cylinderhondas] 2cylinderhondas@yahoogroups.com
> > wrote:
> Hello,
> I need a set of the gaskets between the tail light assembly and the body on my 1972 Honda 600 Coupe.
> Is there any place to purchase NOS or reproductions?

[Nobutoshi Hayashi]

They are form gaskets and 1/2" thick. Also they have slotted to fit taillight lens and reverse lens. It will be a little difficult to duplicate with inner tube rubber.

On Fri, May 31, 2019, 9:56 PM art Remai
artremai@...
[2cylinderhondas] wrote:
> �
> I did that to sandwich the window in the medal rails of the driver and passenger window. Bicycle inner tube worked well.
> Sent from my iPhone
> On May 31, 2019, at 6:46 PM, J Graf
> jgraf@...
> [2cylinderhondas] 2cylinderhondas@yahoogroups.com
> > wrote:
> > �
> > When I put my tail light assemblies back on next week, I'm planning on copying the original gasket shape and cutting it out of a left over inner tube.
> > > On May 31, 2019, at 1:39 PM, Chuck Dean
> > > cadean329@...
> > > [2cylinderhondas] > > 2cylinderhondas@yahoogroups.com
> > > > wrote:
> > > �
> > > Hello,
> > > I need a set of the gaskets between the tail light assembly and the body on my 1972 Honda 600 Coupe.
> > > Is there any place to purchase NOS or reproductions?

[james brown]

Did you try Bill Colford at
Bill Colford's parts for the Honda 600 Coupe and Sedan
Bill Colford's parts for the Honda 600 Coupe and Sedan

On Friday, May 31, 2019, 10:10:47 PM EDT, Nobutoshi Hayashi dino246.nobutoshi@... [2cylinderhondas] wrote:

[ Attachment(s) from Nobutoshi Hayashi included below]
They are form gaskets and 1/2" thick. Also they have slotted to fit taillight lens and reverse lens. It will be a little difficult to duplicate with inner tube rubber.
On Fri, May 31, 2019, 9:56 PM art Remai artremai@...
[2cylinderhondas] wrote:
> When I put my tail light assemblies back on next week, I'm planning on copying the original gasket shape and cutting it out of a left over inner tube.
> > On May 31, 2019, at 1:39 PM, Chuck Dean
> > cadean329@...
> > [2cylinderhondas] > 2cylinderhondas@yahoogroups.com
> > > wrote:
> > Hello,
> > I need a set of the gaskets between the tail light assembly and the body on my 1972 Honda 600 Coupe.
> > Is there any place to purchase NOS or reproductions?
[/quote]

[Chuck Dean]

Hello, Bill told me that he uses 1/4 inch vacuum hose that he splits and puts around the tail light housing. Then he uses car wax to shine it like new.
I'll stick with his idea... He's build a lot of these cars.
Chuck  (mobile) Pleez x cuze enny tie ping or spelin air ores.
Our 1972 Honda 600 Coupe Our 1961 Vespa 400

On May 31, 2019, at 7:16 PM, james brown
zulinicomics@...
[2cylinderhondas] wrote:
Did you try Bill Colford at
Bill Colford's parts for the Honda 600 Coupe and Sedan
Bill Colford's parts for the Honda 600 Coupe and Sedan
On Friday, May 31, 2019, 10:10:47 PM EDT, Nobutoshi Hayashi
dino246.nobutoshi@...
[2cylinderhondas] wrote:
[
Attachment(s)
from Nobutoshi Hayashi included below]
They are form gaskets and 1/2" thick. Also they have slotted to fit taillight lens and reverse lens. It will be a little difficult to duplicate with inner tube rubber.
On Fri, May 31, 2019, 9:56 PM art Remai
artremai@...
[2cylinderhondas] wrote:
> I did that to sandwich the window in the medal rails of the driver and passenger window. Bicycle inner tube worked well.
> Sent from my iPhone
> On May 31, 2019, at 6:46 PM, J Graf
> jgraf@...
> [2cylinderhondas] 2cylinderhondas@yahoogroups.com
> > wrote:
> > When I put my tail light assemblies back on next week, I'm planning on copying the original gasket shape and cutting it out of a left over inner tube.
> > > On May 31, 2019, at 1:39 PM, Chuck Dean
> > > cadean329@...
> > > [2cylinderhondas] > > 2cylinderhondas@yahoogroups.com
> > > > wrote:
> > > Hello,
> > > I need a set of the gaskets between the tail light assembly and the body on my 1972 Honda 600 Coupe.
> > > Is there any place to purchase NOS or reproductions?

[TOM THIES]

That is what I used. Cut it a bit longer, mine shrunk about an eight of an inch
Sent from me

On May 31, 2019, at 7:29 PM, Chuck Dean
cadean329@...
[2cylinderhondas] wrote:
Hello,
Bill told me that he uses 1/4 inch vacuum hose that he splits and puts around the tail light housing. Then he uses car wax to shine it like new.
I'll stick with his idea... He's build a lot of these cars.
Chuck  (mobile)
Pleez x cuze enny tie ping or spelin air ores.
Our 1972 Honda 600 Coupe
Our 1961 Vespa 400
On May 31, 2019, at 7:16 PM, james brown
zulinicomics@...
[2cylinderhondas] wrote:
> Did you try Bill Colford at
> Bill Colford's parts for the Honda 600 Coupe and Sedan
> Bill Colford's parts for the Honda 600 Coupe and Sedan
> On Friday, May 31, 2019, 10:10:47 PM EDT, Nobutoshi Hayashi
> dino246.nobutoshi@...
> [2cylinderhondas] 2cylinderhondas@yahoogroups.com
> > wrote:
> [
> Attachment(s)
> from Nobutoshi Hayashi included below]
> They are form gaskets and 1/2" thick. Also they have slotted to fit taillight lens and reverse lens. It will be a little difficult to duplicate with inner tube rubber.
> On Fri, May 31, 2019, 9:56 PM art Remai
> artremai@...
> [2cylinderhondas] 2cylinderhondas@yahoogroups.com
> > wrote:
> > I did that to sandwich the window in the medal rails of the driver and passenger window. Bicycle inner tube worked well.
> > Sent from my iPhone
> > On May 31, 2019, at 6:46 PM, J Graf
> > jgraf@...
> > [2cylinderhondas] > 2cylinderhondas@yahoogroups.com
> > > wrote:
> > > When I put my tail light assemblies back on next week, I'm planning on copying the original gasket shape and cutting it out of a left over inner tube.
> > > > On May 31, 2019, at 1:39 PM, Chuck Dean
> > > > cadean329@...
> > > > [2cylinderhondas] > > > 2cylinderhondas@yahoogroups.com
> > > > > wrote:
> > > > Hello,
> > > > I need a set of the gaskets between the tail light assembly and the body on my 1972 Honda 600 Coupe.
> > > > Is there any place to purchase NOS or reproductions?

[Bill]

Take a look here to fine other universal rubber parts from Steel Rubber products inc.� some universal rubber parts will work.
https://d163axztg8am2h.cloudfront.net/s ... 4d688b.pdf
Bill

[J Graf]

Excellent, Bill. Thanks for the link. I downloaded the pdf for reference. I need rear quarter window gaskets for one of my sedans.

> On Jun 1, 2019, at 12:25 AM, 'Bill'
> billmyong@...
> [2cylinderhondas] 2cylinderhondas@yahoogroups.com
> > wrote:
> Take a look here to fine other universal rubber parts from Steel Rubber products inc.  some universal rubber parts will work.
> https://d163axztg8am2h.cloudfront.net/s ... 4d688b.pdf